Custom verification kits for every PCB revision.

American company · San Francisco, CABacked by Combinator

Agonic AI Instant quote

Pricing

Pricing for a custom PCB verification kit

A kit is priced from a few counts for your board. You see the quote as you type. A typical kit is $1,925, or $962.50 with the early-partner coupon.

Updated November 15, 2026 · Markdown version

How is the price worked out?

The kit price is a base price plus a rate for each thing your board needs. All prices are in US dollars.

LinePriceWhat it counts
Base kit$1,695The interposer board, the probe dock, cables and design review.
Test point$3 eachSignal and power nets to probe. Ground probes are included.
Instrument connection$10 eachOne per bench port you plug in: a supply channel, a multimeter, each scope channel, an analyzer port, a programmer.
Ribbon or flex connector$5 eachRibbon (IDC) and flex (FFC or FPC) connectors on your board that the dock reaches signals through.

Kit price = $1,695 + $3 × test points + $10 × instrument connections + $5 × ribbon and flex connectors + special requirements.

What do special requirements cost?

Leave these at zero if none apply to your board.

Special requirementPriceWhat it counts
High voltage$12 per pointTest points that can exceed 60 V DC. They are also counted as test points. 60 V is the line we use for pricing, not a rating. Above 1,000 V is confirmed at design review.
High current, 2 to 10 A$2 per pointPoints where the dock supplies or loads the board. Points that are only measured do not count. Also counted as test points.
High current, above 10 A$25 per pointAs above, for points above 10 A.
High speed and RF$80 per signal or portSignals probed through coax (a differential pair is 2) and RF ports. Each comes out on its own SMA connector. Do not also count these as test points.
Two-sided probing$65A second probe plate for the other side of the board. Up to 10 points on the second side are already in the base kit.

What does a typical kit cost?

BoardKit priceWith EARLYPARTNERWith FIRSTKIT
Small: 20 test points, 4 instrument connections$1,795$897.50$1,077
Typical: 50 test points, 8 instrument connections$1,925$962.50$1,155
Larger: 120 test points, 12 instrument connections, 2 flex connectors, 4 high-speed signals$2,505$1,252.50$1,503
Large, two-sided: 200 test points, 16 instrument connections, 8 flex connectors, 8 high-speed signals, 2 RF ports$3,360$1,680$2,016

Larger boards are welcome. Above 200 test points, 16 instrument connections or 8 ribbon and flex connectors, the price is often higher after design review.

To price your own board, use the instant quote on the home page. Software can ask for the same quote at https://agonicai.com/api/quote; see For AI agents.

Which coupons are there?

There is a limited number of coupons. One code applies per kit.

CodeDiscountWho it is for
EARLYPARTNER50% off your first kit, up to $2,000 off. Then 20% off each of your next 5 kits, up to $1,000 off each, when ordered within 12 months of the first.Early partners. One per company. We ask for a feedback call after each kit, your logo on our site, and a case study you approve.
FIRSTKIT40% off the first kit you order, up to $1,500 off.Companies that have not ordered a kit before. One per company.

A coupon applies to the kit price we confirm after design review, not to software, shipping or taxes. Coupons cannot be combined.

Is the quote the final price?

The quote is the price for the counts you enter. We confirm the price after design review, when we check the counts against your design files. If the price changes, you approve the new price before we build.

What is included, and what is not?

The price is for the kit hardware: the custom interposer board, the custom probe dock, cables between them, and design review.

Not included: the test agent software, shipping, taxes and duties, and the cables from your bench instruments.

How long does a kit take?

The kit is built while your PCB is in fab. When you order, you choose the turnaround you need (1 week, 2 weeks, 4 weeks, or flexible), and we confirm the ship date with your order.

How do I order?

  1. Open the instant quote and enter the counts for your board.
  2. Add your design files: the schematic and layout for one board revision. A BOM is optional. Up to 20 files, 90 MB in total.
  3. Add the kit to the cart, enter your name, email, company, shipping address and turnaround, and place the order.

You get a confirmation email with everything you submitted. The order form does not take payment.